● Load meets or exceeds the following standards: ASTM E4, ISO7500-1, EN 10002-2, BS1610, DIN 51221.
● Strain measurement meets or exceeds the following standards: ASTM E83, ISO 9513, BS 3846, EN 10002-4.
● Safety: This machine shall conform to all relevant European CE Health and Safety Directives EN 50081-1, 580081-1, 73/23/EEC, EN 61010-1.
According to load capacity & test application, the load frames are available in single column, table and floor type to meet a variety of test applications.
Single column machine is more suitable for bio-medical, textiles, plastic film industries where load testing requires a lower capacity (below 5kN). Dual-column is the main choice of rubber, plastic, composites, metal alloy, and fasteners, whose specimen needs a wide test area, middle strength, and high capacity.
The frames all take human factors into considerations in the design to ensure the safety, reduce operators’ fatigue and provide the highest flexibility. The extremely robust cross-head guidance is incorporated in all frame designs so as to provide the highest stiffness of lateral cross-heads.
Load cell is with high accuracy and interchangeable for all frames. Each frame is allowed to operate in full capacity.
The electromechanical testing machine for local components stops automatically when the change in the test force exceeds a specified value during operation.
Large space in the working area:
The insides of columns provide wide space for the operator.
The range of the cross-head movement is mechanically limited.
Comfortable working area:
The wide legroom under the load unit provides a comfortable working area for attaching and removing jigs.
Load measuring range
2%~100% of F.S
±1% of the reading
Deformation measuring range
2%~100% of F.S
±1% of the reading
Vertical test space (mm)
Total crosshead travel (mm)
Column spacing (mm)
Max. tensile space (mm)
Max. compression space (mm)
Tensile jaw for round specimen(mm)
Tensile jaw for flat specimen (mm)
Width x height of jaw (mm)
40 x 50
Compression platen diameter (mm)
Bending fixture span(mm)
Length of bending roller (mm)
Diameter of bending roller (mm)
of bending supporter (mm)
Frame axial stiffness (kN/mm)
1 phase, 220V/110V, 50Hz/60Hz
1150 x 810 x 2285
1150 x 810 x 2485
1. Single column machine equips with screw action parallel grip for flat specimens.
2. Single column machine is not configured with bending fixture as standard, it can be specially offered.
3. Appearance and specifications are subject to change without advance notice.
4. Equipment of other dimensions (extra height & extra width) & capacities can be offered in accordance to the necessity of customers.
5. The economic series electromechanical UTM are ideal for spring testing. Model shall be WDW-T***E when ordering;
WDW-L Series Electric Vertical Test Stand
WDW-L series Electric Vertical Test Stand is a tensile compressive test stand especially designed to match push-pull force gauge. This series pf electric vertical test stand has good stability, wide application range and is convenient to use. The electric vertical test stand has stepless speed-adjusting uniform motion, digital display of the testing speed and converting mode between manual and automatic operation. The vertical test stand is specialized for tension/compression test, insertion/withdraw test, fatigue test and fracture test.
Max. Load (kN)
Load Speed (mm/min)
50-245(Max Load: 200N); 250-500(Max Load: 500N)
50-245(Max load: 500N); 250-500(Max Load:1000N)
Applied with (purchase additionally):
1. SN, SH/SP (Sensor Inside) push pull force gauge
● Verification of Testing Frame and Specimen Alignment：ASTM E1012.
Electromechanical Universal Testing Machine
Hydraulic Universal Testing Machine
Impact Testing Machine
Dynamic Testing System
Creep and Rupture Testing Machine
Compression Testing Machine
Upset Testing Machine
Bending Testing Machine
Torsion Testing Machine
Cupping Testing Machine
Spring Testing Machine
Friction Wear Testing Machine
Load Cell Calibration System
High Temperature Axial Extensometer
Fracture Mechanics Clip-on Gages
Transverse and Diametral Extensometers
High Temperature Transverse and Diametral Extensometers
Rock,Concrete and Asphalt Extensometers
Averaging,bi-axial and axial torsional extensometers
Bolt prool,lap shear and specialty extensometers
Knife Edges for Extensometers
Interface Electronics and Signal Conditioners
Sample Preparation Machine
Model: WDW-E series
WDW series computer control electromechanical testing machine for local components is designed according to ASTM, ISO, DIN, EN, JIS, GOST, GB standards etc.. It is computer-controlled and precision. Our electromechanical testing machine for local components is widely suitable for metallic and nonmetallic materials for tension, compression, bending, and shearing test.The electromechanical testing machine for local components features as high precision, high stability and high reliability. Graph, test result display, data processing and printing can be done easily by its PC system and printer. Completed with modulus for metal, spring, textile, rubber, plastic and other material test, our electromechanical testing machine for local components is widely used in manufacturers such as industry factories, research and development, test institutes and training centers etc.
WDW-E economical series of electromechanical testing machine for local components adopt rigid load frames, accurate load weighting system, advanced PCIE measuring & control system and intuitive modular application software. Configured with wide range of accessories for applications, the materials testing systems can provide the best testing solutions for your individual application needs.
The economical series of electromechanical testing machine for local components are good at spring testing. The parameters are much better than other spring testing machines existing in the market.
WDW-E economical electromechanical testing machine for local components is an ideal equipment for lower budget project where not a less accuracy of testing results is needed. It equips with reasonable configurations of top local components (load cell, servo motor & driver, encoder, standard screws), which can satisfy the ordinary testing requirements.